Printing3DP - Revision history

Rtwomey at 12:26, 29 November 2016

2016-11-29T12:26:41Z

Rtwomey: /* Check Filament Feed */

2016-11-29T12:25:40Z

‎Check Filament Feed

Rtwomey: /* Check Filament Feed */

2016-11-29T12:24:20Z

‎Check Filament Feed

Rtwomey: /* Check Filament Feed */

2016-11-29T12:24:07Z

‎Check Filament Feed

Rtwomey: /* Preheat Printer */

2016-11-29T12:21:18Z

‎Preheat Printer

Rtwomey: /* Preheat Printer */

2016-11-29T12:19:30Z

‎Preheat Printer

Rtwomey at 12:18, 29 November 2016

2016-11-29T12:18:30Z

Rtwomey: Created page with "=Preheat Printer= #Turn on the creatorbot. Rocker switch is on the back left side. 400px Temp -> Preheat -> Preheat PLA 1 ===Check Filament Feed==..."

2016-11-29T12:17:00Z

Created page with "=Preheat Printer= #Turn on the creatorbot. Rocker switch is on the back left side. 400px Temp -> Preheat -> Preheat PLA 1 ===Check Filament Feed==..."

New page

=Preheat Printer=
#Turn on the creatorbot. Rocker switch is on the back left side.
[[File:power_switch.png|400px]]

Temp -> Preheat -> Preheat PLA 1

===Check Filament Feed===
Visually inspect that filament feeds properly:
#from spool
#through filament sensor (small clip on back for frame)
#through feed motor
#through milky plastic feed tube
#out of extruder hot end.

===Load Filament===
'''Manual Advance Filament'''

Config -> Move -> Extruder -> Extruder #1 '''+25mm'''

*See Creatorbot Manual [{{filepath:CreatorBotManual.pdf}} CreatorBotManual.pdf] (thank you Mark from [http://launchlab.ysu.edu LaunchLab])

@@ Line 15: / Line 15: @@
 *Select menu '''Config->Move->Extruders'''
 *Use the '''+10mm''' and '''+25mm''' to extrude the filament from the hotend. '''NOTE: Must be preheated!'''
 ===Load Filament===

@@ Line 13: / Line 13: @@
 *Preheat printer.
-*Select menu '''Config->Move->Extruders"
+*Select menu '''Config->Move->Extruders'''
 *Use the '''+10mm''' and '''+25mm''' to extrude the filament from the hotend. '''NOTE: Must be preheated!'''

@@ Line 1: / Line 1: @@
 =Preheat Printer=
-*Turn on the creatorbot. Rocker switch is on the back left side. Position 2 for PLA, Position 1 for ABS.
+*Turn on the creatorbot. The power switch is on the back left side. '''Position 1 for ABS, Position 1 for PLA'''.
 [[File:cretorbot_power.png|600px]]
 *In the Creatorbot main menu, select: '''Temp -> Preheat -> Preheat PLA 1'''

@@ Line 1: / Line 1: @@
 =Preheat Printer=
-#Turn on the creatorbot. Rocker switch is on the back left side. Position 2 for PLA, Position 1 for ABS.
+*Turn on the creatorbot. Rocker switch is on the back left side. Position 2 for PLA, Position 1 for ABS.
-[[File:creatorbot_powerswitch.png|400px]]
+[[File:cretorbot_power.png|600px]]
-#In the Creatorbot main menu, select: '''Temp -> Preheat -> Preheat PLA 1'''
+*In the Creatorbot main menu, select: '''Temp -> Preheat -> Preheat PLA 1'''
 ===Check Filament Feed===

@@ Line 4: / Line 4: @@
 *In the Creatorbot main menu, select: '''Temp -> Preheat -> Preheat PLA 1'''
-===Check Filament Feed===
+=Check Filament Feed=
 Visually inspect that filament feeds properly:
 #from spool
@@ Line 17: / Line 17: @@
 [[File:move_extruder.png|400px]]
-===Load Filament===
+==Load Filament==
 '''Manual Advance Filament'''
@@ Line 23: / Line 23: @@
 *See Creatorbot Manual [{{filepath:CreatorBotManual.pdf}} CreatorBotManual.pdf] (thank you Mark from [http://launchlab.ysu.edu LaunchLab])

@@ Line 11: / Line 11: @@
 #through milky plastic feed tube
 #out of extruder hot end.
 ===Load Filament===